|
WE
ARE AUTHORIZED TO SELL ANTHEM AND ANTHEM STATEMENT PRODUCTS IN OUR
LOCAL MARKET ONLY. IF YOU ARE VISITING FROM OUTSIDE OUR LOCAL MARKET,
PLEASE GO TO ANTHEM'S WEBSITE TO FIND THE NAME OF YOUR NEAREST DEALER.
Anthem integrated amplifiers are designed to perform flawlessly - offering stunning musicality, tonal neutrality and incredible dynamics while driving any speaker load reliably under real-world conditions! The power supply is conservatively rated and the amplifiers run cool for greater reliability, but we didn't stop there.
This amplifier features our ALM (Advanced Load Monitoring) circuitry which protects sensitive output devices by constantly monitoring temperature, current and voltage to ensure optimum long-term performance. ALM is totally non-invasive - it is not in the signal path and only engages in the most extreme circumstances
to protect the amplifier from damage by maintaining the safe operating area of the output devices. Buyer beware however! Not all amplifier manufacturers have sophisticated load-monitoring provisions. Many have saved the added cost, leaving their output devices unprotected, choosing instead to use the amplifier's output
devices as "fuses." At Anthem, ALM is just one of the ways in which our products provide owners with years of reliable service.
- PHONO PREAMPLIFIER - The phono preamplifier is suitable for moving magnet and high-output moving coil cartrdiges
- Input Impedance 47 k
- Input Capacitance 100 pF
- Maximum Input 18 mV at 20 Hz, 140 mV at 1 kHz, 160mV at 20 kHz
- Gain (at 1 kHz) 35 dB
- Crosstalk (at 1 kHz) 80 dB
- RIAA Response +/- 0.5 dB (100 Hz to 20 kHz); -1 dB (20 Hz)
- THD+N (at 1 kHz, 5 mV input) 0.05%
- S/N Ratio (ref. 5 mV at 1 kHz, IEC-A filter) 83 dB
- PREAMPLIFIER
- Input Impedance 30 k
- 'Pre-Out' Output Impedance 560
- 'Rec-Out' Output Impedance 100
- Rated Input 1.0 Vrms
- Maximum Input 7.6 Vrms
- Minimum Load 5 k
- Rated Output (100 k load) 1.0 Vrms
- Maximum Output (100 k load) 7.6 Vrms
- Headphone Output 500 mW into 32 at 0.03% THD+N
- Channel Separation (at 1 kHz) 75 dB
- Crosstalk Between Inputs (at 1 kHz) 72 dB
- XLR Pin Configuration Pin 1: Ground; Pin 2: Positive; Pin 3: Negative
- Frequency Response and Bandwidth 20 Hz to 20 kHz (+0, -0.1 dB); 1 Hz to 170 kHz (+0, -3 dB)
- THD+N (at rated input and output, 80 kHz BW) 0.003%
- IMD (CCIF at 15 kHz and 16 kHz) 0.0005%
- S/N Ratio (A-weighted, ref 2.0 Vrms) 105 dB
- POWER AMPLIFIER (per channel, continuous RMS, 20 Hz to 20 kHz, <1.0% THD)
- Impedance
- 8 ohms both channels driven 225 watts per channel
- 4 ohms both channels driven 310 watts per channel
- Frequency Response 20 Hz to 20 kHz (+0, -0.15 dB)
- Bandwidth 1 Hz to 200 kHz (+0, -3 dB)
- THD+N 0.01% at 1 kHz, 0.03% at 20 kHz (100 W into 8)
- Power Bandwidth < 10 Hz to 100 kHz (+0, -3 dB, 200 W into 8)
- Slew Rate 25 V/µs
- Headroom 1.4 dB (8), 2.8 dB (4)
- Damping Factor 80 at 1 kHz (ref. 8)
- S/N Ratio (A-weighted, ref 225 W) 105 dB
- Crosstalk > 57 dB (100 Hz to 10 kHz)
- Voltage Gain 29 dB
- CONTROL
- Infra Red Carrier Frequency 38 kHz
- Max. Emitter Current Pass-through of input
- Trigger
- Input Polarity Non-polarized
- Output Pass-through of input
- POWER REQUIREMENTS
- Power Consumption (8 load)
- Maximum 800 W
- Typical 300 W
- Fuse Rating (Fuse is internal) Anthem serviceable only
- Low Voltage Version: In countries where the line voltage is 120V, this product operates from a single phase AC power source that supplies between 108V and 132V at a frequency of 60 Hz.
- High Voltage Version: In countries where the line voltage is 220V, 330V or 240V, this product operates from a single phase AC power source that supplies between 216V and 264V at a frequency of 50 or 60 Hz.
- Dimensions
- Height 5-7/8 inches including feet
- Width 17-1/4 inches
- Depth 18 inches
- Weight (Unpacked) 42.6 lb
|
